The CineRun from GepRC is undoubtedly one of the best 3″ cinewhoops in its class in terms of flight performance.  The super rigid frame coupled with a dual gyro F7 flight controller couple with a pro tune, essentially remove any wobbles in your footage.  This means with the cinerun, you can capture that perfect cinematic shot.

DJI FPV air unit is not included with this kit, but it can easily be installed.  Unless you are using the DJI FPV remote, you will need to install your own receiver (soldering may be required).

Features

• No Propellers  in the view.
• Perfect for DJI FPV HD(720p 120fps FPV)
• Equipped with a 3-inch guard frame, Ensure safety and reliability
• Full 3K Carbon Fiber
• System:STABLE PRO F7 35A
• Black Box: 32Mb onboard flash memory.
• Full Soft Mounted FC System: Provides a clean operating environment for gyro.
• Exquisite Assembly Process: Eliminate any potential installation problems.
• Weight:203g(without battery and GoPro Mounts TPU)

Specifications

• Full 3K Carbon Fiber
• Side plate : 1.5mm
• Top plate : 2mm
• Bottom plate : 3mm
• Side plate : 2mm
• Wheelbase : 155mm
• Motors: GR1404 3850KV
• Recommended Battery：4S 850mAh (No inclued)
• Recommended Camera：GoPro Hero 7/8(No inclued)

Features

Frame

• Frame:3mm 3k carbon fiber
• Flight Controller:Kakute F7 HDV
• ESC:Tekko32 F3 4in1 45A mini ESC
• VTx: Caddx Vista Digital HD System for DJI HD FPV
• Motor：F1507 KV3800
• Propeller：T3140
• Buzzer included.
• Battery plug: XT30
• Wheelbase: 148.6mm
• Weight:176g（included CADDX FPV Vista）
• Recommend battery: 650mah~1300mah 4s

FPV SYSTEM : DJI FPV Air Unit

• Operating Frequency: 5.725-5.850 GHz
• Transmitter Power (EIRP): FCC/SRRC: <30 dBm; CE: <14 dBm
• Min. Latency (end-to-end)
• Low Latency Mode (720p/120fps): <28 ms
• High-Quality Mode (720p/60fps): <40 ms
• Max. Transmission Distance: FCC/SRRC: <4 km; CE: <0.7 km
• Video Format: MP4 (Video format: H.264; Audio format: ACC-LC)
• I/O Interface: USB-C, MMCX, 3-in-1 port, microSD card slot
• Operating Temperature Range: 32° to 104°F (0° to 40°C)
• Input Power: 7.4-17.6 V, about 4-9 W
• Sensor: 1/3.2” CMOS; Effective Pixels: 4 M
• Lens: 2.1 mm, f/2.1
• Shutter: Rolling shutter
• ISO: 100-25600
• FOV: 150°(D); 122°(H); 93°(V)
• Dimension: 22.1 × 21.1 × 20.1 mm

STABLE PRO F7 Flight Controller Specs：

• Model:STABLE PRO F7 35A
• MCU: STM32F722RET6
• IMU: 2x ICM20689(SPI)
• BlackBox: 32Mb onboard Flash
• OSD: BetaFlight OSD w/ AT7456E chip
• Baro:NO
• BEC Output: 5V@3A
• Integrated LC Filter
• Input Voltage: 2-6S Lipo
• Firmware target: EXF722DUAL
• Size: 26x26mm board, 20mm mounting holes (M2)

STABLE PRO F7 ESC BL32 2-6S 4in1 Specs：

• MCU:STM32F051
• Constant:35Amps
• Burst:45Amps
• Dimensions:31*31mm(including the power pads)
• Mounting Holes:20*20mm,M2
• Supports Dshot1200,Proshot,Oneshot,Multishot
• Current meter: Yes
• Target: GEPRC-BL32-4IN1

Includes:

• 1x CineRun HD3 Quadcopter
• 1x GoPro 7 Mounts TPU
• 4x 3inch Props(pairs)

Still Required

• R/C Transmitter (also receiver if you are not using the DJI FPV remote)
• DJI FPV Goggles
• 650-1300 4S Lipo (at least 60C)