SkyStars F7 HD Pro 2 + KM50 Flight Stack - SkyStars

Product overview

Part Number: SkyStars F7 HD Pro 2 + KM50 Flight Stack

Manufacturer: SkyStars

Product Category: STACK, CONTROLLER AND ESC

Update Date: 2024-05-20

Description

The SkyStars Fly Tower Stack features an F722 HD Pro3 Flight Controller and a KM50 Pro 50A 3-6S 4-in-1 BLHeli_32 ESC with a 30×30 mounting pattern.

Detailed Information

Features

1. Solder pads are the largest in size compared to other FC in market.

2. Proper solder pad spacing to avoid solder bridge and facilitate easy soldering.

3. ESC connector on top-side rather than bottom which makes it easy for repair.

4. Support ELRS receiver row pin straight mounting.

5. TVS Diode for Reverse Polarity Protection and Voltage Spike Suppression.

6. Powerful BEC to supply all your electronics.

7. Pads arrangement are executed in such a way that when you twist the wires of the camera VTX and RX you don’t get any wire overlapping this gives you a uniform twist and clean look.

8. DJI connector on the top side.

9. Budget-friendly price ( We understand the situation of chip shortage and rising prices of FC )

10. Two stages of Quality check to reduce any faulty electronic.

11. No power lines near Gyro to avoid any EMI interference.

12. Comes ready with I2C support and INAV.

Specifications

Flight Controller

MCU: STM32F722RGT6 216MHz
Gyroscope: BMI270
Baro:Bmp280
OSD: Betaflight SPI OSD DJI HD OSD(UART6)
Black box: 16MB
6x Uarts: UART 1/2/3/4/5/6
4x PWM outputs
1x I2C
3x LEDs for FC STATUS (Blue, Green) and 3.3V indicator(Red)
USB Type-C(USB2.0)
1x JST-SH1.0_8pin connector (Gnd/Vbat/S1/S2/S3/S4/Rx3/Curr)
1x JST-SH1.0_6pin connector (R1/G/R6/T6/G/10V)
VTX 10V/Vbat filtered power ON/OFF switch
DJI FPV OSD is supported by any spare UART
LED: 4 LED independent pads, support WS2812 programming lamp output.
Receiver: Support Sbus, crsf, ibus, SBUS, XBUS, support 3.3v Spektrum satellite receiver, The default receiver input is UART1(You can solder ELRS RX on UART1), F7 has a built-in inverter, which can be installed in any spare UART.

Power

Input voltage: 3-6S
BEC: 5V/10V 3A max dual-channel BEC supports stable power supply on the sky side of DJI
LDO 3.3V: Max.250mA

FC Firmware

BetaFlight firmware: SKYSTARSF722Pro
INAV firmware: SKYSTARSF722HD

Mounting

Installation size: 30.5mm × 30.5mm The installation hole is M4 and supports shock column installation
External size 39mm × 39mm
Flight control weight: 6.9g
Flight control onboard voltage sensor.

KM50 PRO 50A ESC

Mounting Hole Pattern : 30.5mm / M3
Input voltage : 3-6S LiPo / LiHV
ESC Protocol : Dshot 600/1200
Product size : 41x46x7.6mm
Overcurrent Protection : Yes
Peak Current : 60A (10S)
Continous Current : 50A
Firmware : Blheli_32
Weight : 17g
BEC : NO

Includes

1x F7HD Pro3 FC
1x KM50 128K BL32 4IN1 ESC
Connector Cables

Skystars%20f7%20pro%20stack%20info

Price & Procurement

Associated Product

canopic jar 3d printing

Material: TPU Weight: up to 1g. Suitable for cameras: Caddx Ant lite, C ...
dipole antenna 5.8g ipex 7cm

Dipole antenna 5.8G ipex 7cm
dipole antenna 5.8g ipex 5cm

Dipole antenna 5.8G ipex 5cm
connector a30 male/female

A30 Male/Female Connector
canopy crux3

Weight: 1.2 g. Canopy for installing cameras: 14*14mm
battery GNB 300mah 1s 60c hv

Capacity: 300 mAh Nominal voltage: 3.8 V Maximum discharge current: 60C ...
GEPRC DarkStar20 O3 ELRS Cinewhoop Quadcopter

DarkStar20: So light, it makes feathers look overweight. Perfect for sneaking th ...
CrazyF411 ELRS AIO Toothpick Flight Controller (20A)

With 20A Blheli_s ESCs and an integrated ELRS RX, this FC lifts your drone’s per ...
Tiny1-C

256×192/160×120 Micro Thermal Camera. Tiny1-C is a long-wave (8~14μm) thermal ca ...