DarwinFPV F411 3-4S 30A Stack: The Low-cost Pathway to Soaring Heights!

Don’t let your wallet pull you down when your dreams are soaring high in the skies. Join hands with the most budget-friendly co-pilot you could ask for, the DarwinFPV F411 3-4S 30A Stack. Lovingly engineered for entry-level FPV drone enthusiasts, it’s the Robin to your Batman, the Chewbacca to your Han Solo – an essential ally in your high-flying endeavours. And oh boy, do we have it armored!

This stack doesn’t just stand by your side; it valiantly takes a hit for you! We’ve smothered the flight control and ESC with a robust glue coat, creating a superhero shield against frequent novices’ blow-ups. It’s like an FPV pilot’s suit of armor, on a budget!

Key Product Highlights:

• Glue-treated Goodness: With an exclusive glue coat, we’ve taken the defense to the next level. It’s like a forcefield against metal particles, sand, gravel, weeds, or even pesky dewdrops. The DarwinFPV Stack is more protected than a baby kangaroo in its mother’s pouch!
• Feature-Rich and Feather-Light: This stack sports a built-in barometer, SD card slot, and a bunch of rich interface resources. It’s the Swiss Army Knife of FPV stacks!
• Image Stability: This stack’s FC integrates an LC filter, reducing VTX interference from system voltage changes during drone acceleration and deceleration. It’s like a stabilizing rod for your image quality, so you can enjoy smooth and clear flight footage.
• Firmware Compatibility: Note to the tech aficionados out there! Currently, the black box function of the firmware “DARWINF411” may not be compatible with Betaflight 4.3.0 and 4.3.1, but we’re expecting it to be included in the official 4.3.2 version. If you need to use the black box urgently, please upgrade to the 4.4.0 development version or downgrade to 4.3.0_RC3 and below firmware version.
• Receiver Support: This stack can work with receivers of most protocols out there. From Frsky XM/XM+/R-XSR, Futaba Receiver, DSM/DSMX, FlySky Receiver, TBS Crossfire Receiver, AC900 to PPM, PWM, IBUS, SBUS, SPEKTRUM, and CRSF of ELRS. It’s like the United Nations of receiver support!

Specification

FC

MCU：STM32F411

Gyro：MPU6500

OSD：AT7456E

Black box：built-in SD Card slot

Firmware：DARWINF411

BEC output：5V

Input Voltage：3-6S LIPO

Reserved Connector: 1x SBUS(RX1 inverter)、2x Uarts(1,2）、2x Softserial、1x I²C、1x RGB、1x Buzzer、1x USER(A15)、1x USB

Pcb Size：37mm x 37mm

Mounting Holes：20mm x 20mm、30.5mm x 30.5mm

Attention!!! Because the black box function of the target firmware “DARWINF411” is currently not compatible with Betalight 4.3.0 and 4.3.1 (the black box function is expected to be added to the official version 4.3.2) If you need to use the black box urgently, please upgrade to the 4.4.0 development version or downgrade to 4.3.0_RC3 and below firmware version.

ESC

MCU：EFM8BB21

Continuous Current：30A

Peak Current：35A （10S）

BEC output：Non

Input voltage：3-4S LIPO

Throttle Signal：Dshot600、Oneshot125

Current Sensor： Non

MOS：3 x3

Target：G_H_30

PCB Size：29mm x 31mm

Fixed Hole：20mm x 20mm

Weight：4.9g

Receiver Support：

Frsky XM/XM+/R-XSR

Futaba Receiver

DSM/DSMX

FlySky Receiver

TBS Crossfire Receiver

AC900

It supports receivers of most protocols on the market, such as PPM, PWM, IBUS, SBUS, SPEKTRUM and CRSF of ELRS.

In the Box:

Every DarwinFPV 3-4S F411 FC 4 IN 1 30A ESC STACK comes with a 20AW power cable, XT30, cable pack, 1.8cm 6Pin single SH1.0 wire, and a sticker for a complete, out-of-the-box solution.

In short, if you’re on the hunt for the most cost-effective FPV stack to assemble yourself, look no further! The DarwinFPV F411 3-4S 30A Stack is the Holy Grail you’ve been seeking!

So why wait? Jump onboard, fasten your seatbelt, and let’s conquer the skies together. After all, the sky’s not the limit when there are footprints on the moon!