Product overview
- Part Number
- Happymodel SuperX HD ELRS AIO Flight Controller (1-2S)
- Manufacturer
- Happymodel
- Product Category
- STACK, CONTROLLER AND ESC
- Update Date
- 2024-05-20
Description
Detailed Information
Are you an FPV fanatic desperately seeking a flight controller that integrates the trifecta of power, precision, and endless customization? Does your quest for the ultimate “digital whoop” experience keep you up at night, flipping through forum after forum? Well, you can finally rest easy, mate. The SuperX HD ELRS 1-2S AIO Flight Controller is your silver bullet!
The Agony of Average Stops Here!
Key Highlights:
- Betaflight 4.4.2 Firmware-Ready: No more outdated software; we’re talking the latest and greatest.
- Built-in 12A 4in1 ESC and UART ELRS Receiver: The Holy Grail of digital whooping—ALL-IN-ONE.
- Bluejay ESC Firmware Ready: Yup, no compatibility drama here.
- ExpressLRS V3.0.1 Pre-Installed: So fast, it would make a peregrine falcon jealous.
- No Betaflight Analog OSD Chip: Because who needs this on their HD flight controller?
A Closer Look: The Tech Under the Hood
| Flight controllerSuperX HD ELRS | Betaflight 4.4.2 firmware ready Firmware target: CRAZYBEEF4DX MCU:STM32F411CEU6 (100MHz, 512K FLASH) Sensor: BMI270 or ICM42688P (SPI connection) Power supply: 1-2S Lipo Lihv battery input (DC 2.8V~8.7V), only support 1s input for this drone Built-in 12A(each) Blheli_S 4in1 ESC Dshot300 read Built-in UART elrs receiver , elrs v3.0 ready, support WIFI and pass-through firmware update Bluejay ESC Firmware ready Built-in 5V 1.5A(Max) BEC Built-in voltage detectionBuilt-in currents meter No betaflight analog osd chip Antenna:enamel copper wire |
| Onboard 4in1 ESC | Power supply: 1-2S LiPo/LiPo HV Current: 12A continuous peak 15A (3 seconds) Support ESC-Configurator and BLHELI_S Suite configurator Factory firmware: Z-H-30 – Bluejay, 0.19, 48kHz Default protocol: DSHOT300 |
| Onboard UART ExpressLRS 2.4GHz Receiver | RF Frequency: 2.4GHz Antenna: enameled copper wire 31mm length Telemetry output Power: <12dBm Receiver protocol: CRSF Default firmware version: ExpressLRS V3.0.1 The same hardware with Happymodel EP1 receiver Could update firmware via ExpressLRS configurator or WIFI or Betaflight pass-through |
A Word of Warning
Before you dive in, note that you should possess the soldering skills of a Zen master. Those tiny pads require a steady hand and a focused mind. And just to be crystal clear—any damage due to soldering mishaps is on you, buddy.
Time to Elevate Your Game
This flight controller is like the Swiss Army knife of the FPV world. You get reliability, customization, and performance, all rolled into one. Why settle for less when you can pilot the best?
So, click that “Add to Cart” button now and embrace the future of FPV flying. Trust us, this is the upgrade you didn’t know you needed. But you’ll wonder how you ever flew without it.
FAQs
Q: Can I update the firmware easily? A: Absolutely! The ELRS receiver supports updates via ExpressLRS configurator, WiFi, or Betaflight pass-through.
Q: Is this compatible with my Happymodel EP1 receiver? A: Yes, it’s the same hardware!
Q: What about warranty? A: Check our Warranty Policies page for the nitty-gritty, but remember: soldering issues are not covered.
Price & Procurement
Associated Product
-
-
-
-
-
-
Capacity: 300 mAh Nominal voltage: 3.8 V Maximum discharge current: 60C ... -
DarkStar20: So light, it makes feathers look overweight. Perfect for sneaking th ... -
With 20A Blheli_s ESCs and an integrated ELRS RX, this FC lifts your drone’s per ... -
