Product overview

Part Number
SpeedyBee F405 V4 BLS 60A 30×30 Stack
Manufacturer
SpeedyBee
Product Category
OTHER PARTS
Update Date
2024-05-20

Description

Ever wanted your drone to handle like a sports car with jet engines? The SpeedyBee F405 V4 & BLS 60A ESC combo is your ticket to making pigeons jealous. For FPV pilots who prefer their drones on beast mode

Detailed Information

The Flight Controller That Thinks It’s a Rocket Scientist

Meet the SpeedyBee F405 V4 Flight Controller: the brain behind your drone’s brawn. With an STM32F405 MCU and ICM42688P IMU, this little genius is like strapping a supercomputer to your drone. It’s so smart, it makes Einstein look like he’s still in kindergarten.

  • USB Type-C: Because we’re not savages.
  • Built-in Barometer: It knows the weather better than your local meteorologist.
  • Direct DJI Compatibility: Plug and play with your DJI gear, because life’s too short for soldering headaches.
  • Blackbox Ready: For when you need to prove it wasn’t pilot error.
  • Power Versatility: From 3S to 6S, it handles power like a seasoned barista handles coffee – perfectly.

The ESC That Believes It’s a Powerlifting Champion

And then there’s the SpeedyBee BLS 60A 4-in-1 ESC. With 60A continuous current and 80A bursts, this ESC doesn’t just manage your motors; it bench presses them.

  • BLHeli_S Firmware: Smooth as butter, sharp as a tack.
  • DSHOT300/600: For when you need to communicate faster than a teenager texting.
  • TVS Protective Diode: It’s like having a bodyguard for your power supply.
  • External Capacitor Included: We’ve thrown in a 1000uF low ESR capacitor, because we’re nice like that.

Why This Combo?

This isn’t just a flight controller and ESC; it’s your ticket to the big leagues. It’s like upgrading from a tricycle to a superbike overnight. Whether you’re a seasoned FPV pilot or a daring newcomer, this combo packs enough punch to make your drone do the Kessel Run in less than twelve parsecs.

Specifications

Product NameSpeedyBee F405 V4 30×30 Flight Controller
MCUSTM32F405
IMU(Gyro)ICM42688P
USB Port TypeType-C
BarometerBuilt-in
OSD ChipAT7456E chip
BLE BluetoothSupported. Used for Flight Controller configuration (MSP should be enabled with Baud rate 115200 on UART4)
WIFINot supported
DJI Air Unit Connection WayTwo ways supported: 6-pin connector or direct soldering.
6-pin DJI Air Unit PlugSupported. Completely compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1, no wire is needed to be changed.
Blackbox MicroSD Card Slot*Betaflight firmware requires the type of the microSD card to be either Standard (SDSC) or High capacity (SDHC) under 32GB, so extended capacity cards (SDXC) are not supported (Many high-speed U3 cards are SDXC). Also the microSD card MUST be formatted with the FAT16 or FAT32 (recommended) format. So, you could use any SD card less than 32GB, but the Betaflight can only recognize 4GB maximum. We suggest you use this 3rd party formatting tool and choose ‘Overwrite format’ then format your card. Also check out here for the recommended SD cards or buy the tested cards from our store.
Current Sensor InputSupported. For SpeedyBee BLS 60A ESC, please set scale = 400 and Offset = 0.
Power Input3S – 6S Lipo(Through G, BAT pins/pads from the 8-pin connector or 8-pads on the bottom side)
5V Output9 groups of 5V output, four +5V pads and 1 BZ+ pad( used for Buzzer) on front side, and 4x LED 5V pads. The total current load is 3A.
9V Output2 groups of 9V output, one +9V pad on front side and other included in a connector on bottom side. The total current load is 3A.
3.3V OutputSupported. Designed for 3.3V-input receivers. Up to 500mA current load.
4.5V OutputSupported. Designed for receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load.
ESC SignalM1 – M4 on bottom side and M5-M8 on front side.
UART6 sets(UART1, UART2, UART3, UART4(Dedicated for Bluetooth connection)), UART5 (Dedicated for ESC telemetry),UART6
ESC TelemetryUART R5
I2CSupported. SDA & SCL pads on front side. Used for magnetometer, sonar, etc.
Traditional Betaflight LED PadSupported. 5V, G and LED pads on bottom of the front side. Used for WS2812 LED controlled by Betaflight firmware.
BuzzerBZ+ and BZ- pad used for 5V Buzzer
BOOT ButtonSupported.
[A]. Press and hold BOOT button and power the FC on at the same time will force the FC to enter DFU mode, this is for firmware flashing when the FC gets bricked.
[B]. When the FC is powered on and in standby mode, the BOOT button can be used to controller the LED strips connected to LED1-LED4 connectors on the bottom side. By default, short-press the BOOT button to cycle the LED displaying mode. Long-press the BOOT button to switch between SpeedyBee-LED mode and BF-LED mode. Under BF-LED mode, all the LED1-LED4 strips will be controlled by Betaflight firmware.
RSSI InputSupported. Named as RS on the front side.
Smart Port / F.PortNot supported
Supported Flight Controller FirmwareBetaFlight(Default), INAV
Firmware Target NameSPEEDYBEEF405V4
Mounting30.5 x 30.5mm( 4mm hole diameter)
Dimension41.6(L) x 39.4(W) x 7.8(H)mm
Weight10.5g
Product NameSpeedyBee BLS 60A 30×30 4-in-1 ESC
FirmwareBLHeli_S J-H-50
PC Configurator Download Linkhttps://esc-configurator.com/
Continuous Current60A * 4
Burst Current80A(10 sec)
TVS Protective diodeYes
External Capacitor1000uF Low ESR Capacitor(In the package)
ESC ProtocolDSHOT300/600
Power Input3-6S LiPo
Power OutputVBAT
Current SensorSupport (Scale=400 Offset=0)
ESC TelemetryNot supported
Mounting30.5 x 30.5mm( 4mm hole diameter)
Dimension45.6(L) * 44(W) *8mm(H)
Weight23.5g

 

What’s in the Box?

  • SpeedyBee F405 V4 Flight Controller: The brain.
  • SpeedyBee BLS 60A 4-in-1 ESC: The muscle.
  • A Bunch of Wizardry: That makes your drone fly like it’s possessed (in a good way).

Get ready to experience flight on a whole new level. With this combo, your drone will be so responsive, you’ll start wondering if it can read your mind. It’s not just flying; it’s transcending.

Price & Procurement

Associated Product