CrazyF411 AIO Toothpick Flight Controller + Receiver (20A ESC, OSD, Frsky RX) - Happymodel

Product overview

Part Number: CrazyF411 AIO Toothpick Flight Controller + Receiver (20A ESC, OSD, Frsky RX)

Manufacturer: Happymodel

Product Category: OTHER PARTS

Update Date: 2024-05-20

Description

The CrazyF411 from Happymodel is an F4 toothpick flight controller with OSD, that also managed to include 4x 20A ESC and a Frsky compatible receiver built into the board, making this flight controller ideal for a very compact and lightweight toothpick build.

Detailed Information

The receiver also includes a PA/LNA power amplifier to enable much greater range compared to some other flight controllers with built in receivers (up to 400m range).

Features

25.5×25.5mm FC AIO ESC board for toothpick .
Most powerful for whoop / toothpick style flight
Supports 2-4s battery input and provides 20A to the motors.
Also Integrated SPI Frsky receiver working with D8/D16 protocols.
This integrated receiver has PA/LNA power amplifier and the diversity antenna., This should give more control range for this flight controller.

Specification

Brand Name: Happymodel

Model: CrazyF411 AIO

Item Name: F4 Flight Controller Built-in 20A BL_S ESC & Frsky Receiver

F4 Flight Controller	MCU:STM32F411CEU6 (100MHZ, 512K FLASH) Sensor: MPU-6000(SPI connection) Board size: 28.5 * 28.5MM Power supply: 2-4S battery input (DC 8V-17V) Built-in 20A(each) Blheli_S 4in1 ESC Dshot600 ready Built-in Frsky D8/D16 SPI receiverBuilt-in 2.4G Power Amplification Built-in Betaflight OSD(SPI Control) Built-in Current meter Built-in 5V 1.5A BEC Built-in voltage detection Firmware target: MATEKF411RX Yaw Degrees should set to “-90 degree” to match the flight direction
Onboard 20A ESC	MCU upgraded to EFM8BB21 Power supply: 2-4S LiPo/LiPo HV (7v/17v) Current: 20A continuous peak 25A (5 seconds) Support BLHeliSuite programmable Factory firmware: F_H_40_REV16_7.HEX Default protocol: DSHOT600
Internal Frsky NON-EU receiver Version	SPI BUS receiver Frsky D8/D16 compatibleCompatible Non EU transmitter both D8 mode and D16 mode Channels: 8ch/16chDual antenna Failsafe support No ground interference ( Transmitter and receiver 1 m from the ground): 400m

Connection Diagram Pinout

How to Bind your receiver

Make the on board receiver get into bind mode: For 4.0.x version firmware Plug USB and then connect betaflight configurator and then move to CLI tab , type “bind_rx_spi” ,the Red LED on the top of the flight controller will getting to be solid , the onboard receiver is in bind mode; For 4.1.x or 4.2.x the bind code is “bind_rx”

Included

1x F4 AIO ESC RX Board
1x Cable with Connector
1x bag of Screws & Standoffs

Price & Procurement

Associated Product

canopic jar 3d printing

Material: TPU Weight: up to 1g. Suitable for cameras: Caddx Ant lite, C ...
dipole antenna 5.8g ipex 7cm

Dipole antenna 5.8G ipex 7cm
dipole antenna 5.8g ipex 5cm

Dipole antenna 5.8G ipex 5cm
connector a30 male/female

A30 Male/Female Connector
canopy crux3

Weight: 1.2 g. Canopy for installing cameras: 14*14mm
battery GNB 300mah 1s 60c hv

Capacity: 300 mAh Nominal voltage: 3.8 V Maximum discharge current: 60C ...
GEPRC DarkStar20 O3 ELRS Cinewhoop Quadcopter

DarkStar20: So light, it makes feathers look overweight. Perfect for sneaking th ...
CrazyF411 ELRS AIO Toothpick Flight Controller (20A)

With 20A Blheli_s ESCs and an integrated ELRS RX, this FC lifts your drone’s per ...
Tiny1-C

256×192/160×120 Micro Thermal Camera. Tiny1-C is a long-wave (8~14μm) thermal ca ...